АППРОКСИМАЦИЯ ГЕОМЕТРИИ КОНТУРА ДУГАМИ
ПРИ КОНТРОЛЕ
ТОЧНОСТИ ИЗГОТОВЛЕНИЯ ДЕТАЛЕЙ ЛЕТАТЕЛЬНЫХ АППАРАТОВ
APPROXIMATION
OF CONTOUR GEOMETRY BY CURVES WHILE CONTROLLING THE
ACCURACY OF
MANIFACTURE OF PARTS AND COMPONENTS FOR AIRBORN DEVICES
Феоктистов Сергей Иванович — доктор технических наук,
профессор, декан ССФ
Sergey I.Feoktistov — Doctor in Engineering,
Professor
Кривенок Антон Александрович — программист ОАО «КнААПО»
Anton A. Krivenok — programmer, JSC «KnAAPO»
Белых Сергей Викторович — кандидат технических наук, доцент
belykh.sergey@mail.ru
Sergey V.Belykh — PhD in Engineering,
Associate Professor, E-mail: belykh.sergey@mail.ru
Перевалов Анатолий Анатольевич — аспирант
Anatoly A. Perevalov — PhD candidate
Станкевич Антон Владиславович — начальник научно производственной
лаборатории технологических процессов ОАО «КнААПО»
Anton V.Stankevitch — Head of Research and
Production Lab for Manufacturing Processes, JSC «KnAAPO»
Аннотация: Рассмотрены проблемы контроля деталей авиационного
назначения, получаемых методами гибки. Обосновано применение аппроксимации
дугами набора точек, полученных в результате контроля с использованием. Дано
решение для определения дуги, проходящей через набор точек с различными
граничными условиями. Приведена оценка влияния граничных
условий
аппроксимации на точность получаемой кривой.
Summary: The problems of accuracy control for aviation technology parts and
components produced by forming/bending are looked into. Approximation by curves
of a set of points acquired as the result of accuracy control using... was
proven. A solution for the task of determining a curve going through a set of
points with different boundary conditions is provided. Estimation of the impact
of the
boundary conditions
of approximation upon the accuracy of the resulting curve is carried out.
Ключевые слова: аппроксимация, геометрия контура, дуга.
Keywords: approximation, contour geometry, curve.
«Ученые записки КнАГТУ». № I
- 1(1) 2010 «Науки о природе и технике», с. 6 – 15
«Scholarly Notes of Komsomolsk-na-Amure State Technical University». Issue I - 1(1) 2010
"Engineering and Natural Sciences"
DOI 10.17084/2010.I-1(1).3
References
1. Feoktistov, S.I. Avtomatizatsiia proyektirovaniia tekhnologicheskikh protsessov i osnastki zagotovitel'no-shtampovochnogo
proizvodstva aviatsionnoy promyshlennosti. / S.I. Feoktistov.
- Vladivostok: Dal'nauka, 2001 - 183 s.
2. Vygodskii M.IA., Spravochnik po vysshei matematike / M.Ia. Vygodskii. - M.: Nauka, 1965 - 872 s.
Ссылка на текст
статьи
© 2010 Feoktistov S. I., Krivenok A.A., Belykh S.V., Perevalov A.A., Stankevitch A.V. This is an Open Access article distributed under the
terms of the Russian Index of Science Citation License
http://www.uzknastu.ru/files/forautors/en/License%20Agreement.doc, allowing
third parties to copy and redistribute the material in any medium or format and
to remix, transform, and build upon the material for any purpose, even
commercially, provided the original work is properly
cited and states its license.
©
2010 Феоктистов С.И., Кривенок А.А., Белых С.В.,
Перевалов А.А., Станкевич А.В. Данная статья находится в Открытом Доступе и
распространяется на условиях лицензии Российского Индекса Научного цитирования
http://www.uzknastu.ru/files/forautors/en/License%20Agreement.doc, в
соответствии с которыми третьи лица имеют право копировать и повторно
распространять этот материал на любых носителях и в
любом формате, а также микшировать, изменять и использовать в качестве основы
для любых целей, в том числе коммерческих, при условии, что на оригинальное
произведение сделаны должным образом оформленные ссылки и что приведена
информация о действующей в отношении него лицензии.